Chevrolet P30 Recalls & Complaints by Model Year
NHTSA lists 25 safety recalls and 39 owner complaints across 25 model years of the Chevrolet P30 (1967–1999). The most-complained-about year is 1994.
Pick your Chevrolet P30 model year
- 1967
- 1970
- 1971
- 1973
- 1974
- 1975
- 1976
- 1977
- 1978
- 1980
- 1982
- 1983
- 1984
- 1985
- 1986
- 1987
- 1988
- 1989
- 1990
- 1991
- 1992
- 1993
- 1994
- 1998
- 1999
| Model year | Recalls | Complaints |
|---|---|---|
| 1999 Chevrolet P30 | 0 | 2 |
| 1998 Chevrolet P30 | 0 | 9 |
| 1994 Chevrolet P30 | 0 | 9 |
| 1993 Chevrolet P30 | 0 | 3 |
| 1992 Chevrolet P30 | 0 | 4 |
| 1991 Chevrolet P30 | 0 | 1 |
| 1990 Chevrolet P30 | 1 | 2 |
| 1989 Chevrolet P30 | 1 | 1 |
| 1988 Chevrolet P30 | 1 | 0 |
| 1987 Chevrolet P30 | 1 | 3 |
| 1986 Chevrolet P30 | 1 | 3 |
| 1985 Chevrolet P30 | 5 | 2 |
| 1984 Chevrolet P30 | 3 | 0 |
| 1983 Chevrolet P30 | 1 | 0 |
| 1982 Chevrolet P30 | 2 | 0 |
| 1980 Chevrolet P30 | 1 | 0 |
| 1978 Chevrolet P30 | 4 | 0 |
| 1977 Chevrolet P30 | 4 | 0 |
| 1976 Chevrolet P30 | 2 | 0 |
| 1975 Chevrolet P30 | 3 | 0 |
| 1974 Chevrolet P30 | 2 | 0 |
| 1973 Chevrolet P30 | 2 | 0 |
| 1971 Chevrolet P30 | 2 | 0 |
| 1970 Chevrolet P30 | 1 | 0 |
| 1967 Chevrolet P30 | 1 | 0 |
What Chevrolet P30 owners complain about
Across all model years, owners have filed 39 complaints with NHTSA. The 1994 model year has the most, with 9.
All Chevrolet P30 recalls (25)
Every NHTSA safety campaign that lists a Chevrolet P30, most recent first, with the model years each one covers.
-
Seats
Seat pedestals for driver and passengers may have a larger than specified slot in the center channel.
Remedy: Replace seat pedestals with pedestals having proper slot size.
Model years: 1987, 1988, 1989, 1990
-
Suspension: lower arm
Left hand lower control arm can crack and could eventually cause the lower ball joint to separate from the control arm.
Remedy: Repair or replace lower left control arm.
Model years: 1985, 1986
-
Seats
Three bolts which attach the sill that supports the base of the seat were omitted; therefore vehicles do not comply with FMVSS 210 and FMVSS 207. Consequence of defect: in the event of a crash, the floor plate could buckle along the inboard side causing the seat pedestal to be imbalanced, and increasing the likelihood of injury to the…
Remedy: Install missing bolts.
-
Tie rod assembly (steering)
During a combined cornering and braking maneuver, the tie rod end could contact the tire wall. Consequence of defect: this contact can cause grooving of the tire, which could eventually result in tire failure and possibly a vehicle crash without prior warning.
Remedy: Replace 16" wheels and tires with 19 1/2" wheels and tires; also, replace speedometer gear to compensate for new size wheels and tires.
Model years: 1985
-
Rim (wheels)
The wheel may develop cracks between the disc and rim. Consequence of defect: if this occurs and is not noticed, the crack could increase around the rim, resulting in separation of the rim from the disc, loss of control and an accident may occur.
Remedy: Replace wheels having the suspected manufacturing code number.
Model years: 1985
-
Fan (engine and engine cooling)
The fan blade, when subjected to high stress levels, can fatigue and break apart at the hub while the engine is running. Consequence of defect: if breakage occurs while hood is open, a person working under the hood or near the truck could be struck by a blade part and be injured.
Remedy: Replace engine fan.
-
Filler pipe and cap (fuel system)
Due to a manufacturing problem with the fuel tank filler pipe, the fuel cap may improperly seal the end of the filler pipe. This fails to conform to the requirements of federal motor vehicle safety standard 301, "fuel system integrity." in the event of a collision, an improperly sealed filler pipe could allow fuel spillage.
Remedy: The dealer will inspect and replace fuel caps on all affected vehicles without charge.
Model years: 1984
-
Filler pipe and cap (fuel system)
In a vehicle impact from the rear, the three piece hoses could separate and result in fuel leakage in excess of the amount permitted by federal motor vehicle safety standard no. 301, "fuel system integrity".
Remedy: A new fuel filler hose will be installed by dealer on all involved vehicles.
Model years: 1982
-
Hoses, lines/piping, and fittings (service brakes)
Vehicles may be subject to abrasive contact between the rear brake hose/pipe assembly and the axle housing with normal brake usage and rear pad wear. Should this condition occur, it could lead to a brake hose/pipe failure, resulting in loss of brake fluid and loss of rear braking action.
Remedy: Dealer will inspect and, if necessary, replace the brake hose/pipe assembly and mounting brackets at no charge.
Model years: 1980
-
Indicator light (parking brake)
The parking brake switch connector contains electrical wires that may be reversed. As a result, the lamp will be activated whenever the ignition is turned on, even though the parking brake is not engaged. This constitutes a non-compliance to federal motor vehicle safety standard no. 105, "hydraulic brake systems". The standard requires…
Remedy: Dealer will inspect and, if necessary, correct the parking brake switch wiring without charge to owner.
-
Labels (equipment)
The involved vehicles do not have a brake fluid reservoir warning which states, "warning, clean filler cap before removing. Use only DOT 3 fluid from a sealed container". This constitutes a non-compliance to federal motor vehicle safety standard no. 105, "hydraulic brake systems".
Remedy: The dealer will install the brake fluid reservoir warning plate without charge to owner.
-
Tank assembly (fuel system)
The fuel tank fusible bushing element may have melted due to extremely high temperatures encountered when the tanks were exposed to direct sunlight rays during chassis storage.
Remedy: The dealer will inspect and, if necessary, replace the fuel tank vent plug without charge to owner.
-
Steering wheel/handle bar (steering)
The intermediate shaft coupling on the involved vehicles may have been machined oversized in the serration area where it attaches to the steering column. This would prevent the coupling from properly tightening on the shaft when the clamp and pinch bolt were installed.
Remedy: Dealer will replace the shaft coupling, if necessary, without charge to owner.
Model years: 1978
-
Master cylinder (service brakes)
On the involved vehicles, the brake master cylinder may have been assembled with reservoir mounting bolts that were improperly processed. This could make these bolts brittle and subject to breaking. If breakage occurs, a brake fluid leak may develop between the reservoir and master cylinder. Loss of brake fluid would adversely affect…
Remedy: Dealer will replace the master cylinder reservoir mounting bolts with an improved type, without charge to owner.
Model years: 1976, 1977
-
Suspension: lower arm
The front suspension control arms were assembled with ball joints which may contain sockets that were not properly heat-treated. This may cause the socket to wear rapidly and allow the ball joint stud to separate from the socket, causing either the left or right wheel suspension to collapse.
Remedy: Dealer will inspect and, where necessary, will replace the ball joints without charge to owner.
Model years: 1975, 1976
-
Multi piece (wheels)
Model years: 1975
-
Suspension: rear
Model years: 1975
-
Hoses, lines/piping, and fittings (service brakes)
Model years: 1974
-
Suspension: upper arm
Model years: 1974
-
Wheels
Model years: 1973
-
Pedals and linkages (service brakes)
Model years: 1973
-
Hoses, lines/piping, and fittings (service brakes)
Model years: 1971
-
Wheels
Model years: 1971
-
Master cylinder (service brakes)
Model years: 1970
-
Hoses, lines/piping, and fittings (service brakes)
Model years: 1967
Other Chevrolet models
- Malibu19,364 complaints
- Silverado 150018,029 complaints
- Impala10,434 complaints
- Tahoe10,032 complaints
- Equinox9,161 complaints
- Silverado8,799 complaints
- Blazer8,192 complaints
- Suburban8,164 complaints
Source: NHTSA recall and complaint databases and EPA fuel economy data, October 2026. Complaint counts are owner reports to NHTSA, not verified defects. Recall counts are safety campaigns that list this model year; whether a particular car was already repaired depends on its VIN. How this data is compiled.