Chevrolet Beretta Recalls & Complaints by Model Year
NHTSA lists 15 safety recalls and 547 owner complaints across 15 model years of the Chevrolet Beretta (1984–2002). The most-complained-about year is 1995.
Pick your Chevrolet Beretta model year
| Model year | Recalls | Complaints |
|---|---|---|
| 2002 Chevrolet Beretta | 0 | 1 |
| 1999 Chevrolet Beretta | 0 | 1 |
| 1998 Chevrolet Beretta | 0 | 2 |
| 1997 Chevrolet Beretta | 0 | 1 |
| 1996 Chevrolet Beretta | 1 | 72 |
| 1995 Chevrolet Beretta | 1 | 93 |
| 1994 Chevrolet Beretta | 2 | 85 |
| 1993 Chevrolet Beretta | 0 | 37 |
| 1992 Chevrolet Beretta | 1 | 52 |
| 1991 Chevrolet Beretta | 1 | 49 |
| 1990 Chevrolet Beretta | 2 | 39 |
| 1989 Chevrolet Beretta | 4 | 51 |
| 1988 Chevrolet Beretta | 4 | 60 |
| 1987 Chevrolet Beretta | 5 | 3 |
| 1984 Chevrolet Beretta | 0 | 1 |
What Chevrolet Beretta owners complain about
Across all model years, owners have filed 547 complaints with NHTSA. The 1995 model year has the most, with 93.
All Chevrolet Beretta recalls (15)
Every NHTSA safety campaign that lists a Chevrolet Beretta, most recent first, with the model years each one covers.
-
Interior lighting
Vehicle description: passenger vehicles. These vehicles were built with the potential for the interior lamps to come on unexpectedly while the vehicles are being driven. This does not meet the requirements of FMVSS no. 101, "controls and displays."
Remedy: Dealers will run a diagnostic test on the lamp control module and, if necessary, replace it.
Model years: 1996
-
Door (structure)
The reinforcement panel that serves as a liftpoint for the frame was omitted from the right side rocker assembly of the frame the vehicles do not conform to the requirements of FMVSS no. 208, "occupant crash protection."
Remedy: Dealers will inspect the vehicles for the presence of the right side rocker reinforcement panel. If the reinforcement panel is not present, dealers will contact chevrolet for further instructions.
-
Suspension: front
The suspension support assemblies do not meet general motors corporation's specification for weld integrity and the affected weld can fail causing the front of the control arm to separate from the suspension support assembly.
Remedy: Install revised suspension supports with adequate weld integrity.
Model years: 1994
-
Switch (exterior lighting)
The service brake stop lamp switch becomes inoperative.
Remedy: Replace the stop lamp switch and correct the wiring in the connector of the stop lamp switch wiring harness.
Model years: 1992
-
Seat belts
The front shoulder belt retractors may have reduced sensitivity of the lock-up feature and would not function in a sudden deceleration or crash.
-
Hood (structure)
Secondary hood latch assembly on these vehicles may not be properly adjusted and could become bent. This will lead to a condition where full primary latch engagement is not attained.
Remedy: Replace the primary hood latch assembly, the secondary hood latch assembly, and the support bracket.
-
Steering wheel/handle bar (steering)
Nut attaching steering wheel may not have been properly tightened during installation.
Remedy: Tighten the nut to the proper torque as necessary.
Model years: 1991
-
Seat belts: rear/other
Owner's manuals were printed with rear center seat belt information omitted.
Remedy: Insert missing information into owners manual.
Model years: 1990
-
Hinge and attachments (structure)
A door hinge (upper or lower) may break while opening or closing the door making it difficult to reposition and close properly.
Remedy: Replace door hinges on both doors.
-
Seats
The front seat frame assembly may contain an improper, missing and/or mislocated weld that could fracture.
Remedy: Replace both front seat assemblies.
Model years: 1989
-
Seat belts
Front seat belt latch plates may not engage the buckle assemblies.
Remedy: Replace improperly functioning buckle assemblies.
Model years: 1989
-
Tank assembly (fuel system)
A fuel tank leak could occur due to small creases on the tank underside cracking during pressure cycling which occurs during normal operation.
Remedy: Replace fuel tank.
Model years: 1989
-
Latch (latches/locks/linkages)
Secondary hood latch assembly may not have been properly adjusted resulting in latch becoming bent.
Remedy: Inspect and replace secondary hood latch assemblies as required.
-
Latch (latches/locks/linkages)
Loss of skid plate could lead to disengagement of both secondary and primary hood latches.
Remedy: Install a secondary latch skid plate and/or secondary latch skid plate retaining screws.
Model years: 1987
-
Latch (latches/locks/linkages)
Secondary hood latch may not properly engage due to contact with support bracket and/or the primary latch return spring. Consequence of defect: if this occurs while vehicle is in motion, hood could open and contact the windshield, affecting the drivers vision area; this could result in a crash without warning.
Remedy: Install secondary latch skid plate on corsica and beretta models. Also, install a revised secondary latch assembly on beretta models.
Model years: 1987
Other Chevrolet models
- Malibu19,364 complaints
- Silverado 150018,029 complaints
- Impala10,434 complaints
- Tahoe10,032 complaints
- Equinox9,161 complaints
- Silverado8,799 complaints
- Blazer8,192 complaints
- Suburban8,164 complaints
Source: NHTSA recall and complaint databases and EPA fuel economy data, October 2026. Complaint counts are owner reports to NHTSA, not verified defects. Recall counts are safety campaigns that list this model year; whether a particular car was already repaired depends on its VIN. How this data is compiled.