Dodge B300 Recalls & Complaints by Model Year
NHTSA lists 21 safety recalls and 5 owner complaints across 14 model years of the Dodge B300 (1971–1988). The most-complained-about year is 1976.
Pick your Dodge B300 model year
| Model year | Recalls | Complaints |
|---|---|---|
| 1988 Dodge B300 | 1 | 0 |
| 1983 Dodge B300 | 1 | 0 |
| 1982 Dodge B300 | 1 | 0 |
| 1981 Dodge B300 | 1 | 0 |
| 1980 Dodge B300 | 1 | 0 |
| 1979 Dodge B300 | 2 | 2 |
| 1978 Dodge B300 | 4 | 0 |
| 1977 Dodge B300 | 2 | 0 |
| 1976 Dodge B300 | 2 | 2 |
| 1975 Dodge B300 | 3 | 1 |
| 1974 Dodge B300 | 2 | 0 |
| 1973 Dodge B300 | 4 | 0 |
| 1972 Dodge B300 | 1 | 0 |
| 1971 Dodge B300 | 9 | 0 |
What Dodge B300 owners complain about
Across all model years, owners have filed 5 complaints with NHTSA. The 1976 model year has the most, with 2.
All Dodge B300 recalls (21)
Every NHTSA safety campaign that lists a Dodge B300, most recent first, with the model years each one covers.
-
Gear position indication (prndl) (power train)
Automatic transmission may contain a park sprag rod assembly that may stick in the tooth butt unengaged position.
Remedy: All involved vehicles will have the park sprag rod assemblies replaced.
Model years: 1988
-
Bumpers (structure)
Vehicles may not meet the requirements of federal motor vehicle safety standard no. 301, "fuel system integrity". In an impact test from the rear, the bumper support structure deformed enough to allow contact of a support bracket with the fuel tank.
Remedy: All recalled vehicles will receive frame reinforcements plus two load-bearing rub strips and protective impact shielding. Additionally, a corner of the bumper bracket will be removed.
Model years: 1981, 1982, 1983
-
Caliper (service brakes)
Due to a combination of disc brake pad wear and turn stop wear on certain vehicles, there may be an increase in brake pedal travel and a reduction in front braking effectiveness following a full turn. Also, a frame crack could develop and could extend through all or most of the rail section.
Remedy: Upon inspection dealer will replace either the left or right turn stop bracket to correct the front brakes. If frame is cracked it will be welded and a rod reinforcement will be installed over the cracked area.
-
Hinge and attachments (structure)
The hinge and roller assemblies supporting the rear of the sliding side door may be subject to failure as a result of processing deficiencies in the aluminum hinge body.
Remedy: Upon inspection all aluminum hinge bodies will be replaced with sintered metal components.
Model years: 1980
-
Frame and members (structure)
The front rail extension may experience fatigue cracking near the area where the power steering gear attaches to the frame. If the crack progresses through most or all of the rail section, steering system free play accompanied by metallic rattle noise will be experienced.
Remedy: Affected vehicles will be weld repaired and a reinforcement rod will be installed over the cracked area.
-
Electrical heating element (visibility)
The involved vehicles contain defective fan blower switches that could in certain instances generate an excess of heat in the instrument panel.
Remedy: The vent fan system will be reduced to a single speed operation to avoid overheating in the instrument panel.
Model years: 1978
-
Air conditioner (equipment)
Condensate water may accumulate in the air conditioning blower housing; there is a high probability that this water will cause the blower motor to fail. Blower motor failure would disable the air condtioning unit and there would be no way to defrost or defog the windshield.
Remedy: Dealer will drill a 1/4 inch drain hole in the bottom of the air conditioning blower housing to prevent water accumulation, without charge to owner.
Model years: 1979
-
Hoses, lines/piping, and fittings (service brakes)
The front brake hose routing may allow interference between the hoses and the tire and wheel assemblies during extreme turning angles.
Remedy: Dealer will replace both left and right front brake hoses and install a new brake hose support bracket to eliminate contact with tire/wheel.
Model years: 1978
-
Suspension: lower arm
Lower control arms may fracture in the area adjacent to the lower ball joint, resulting in separation of the ball joint from the arm.
Remedy: Dealer will increase the strength of both lower control arms by installing welded reinforcements.
Model years: 1979
-
Anchorage (seat belts)
The involved vehicles do not conform to federal motor vehicle safety standard no. 209, "seat belt assemblies", in that they do not have the capability of fitting certain adult passengers when the seat is in the full forward position.
Remedy: Dealer will replace the front passenger unibelt assembly with an assembly having a longer belt webbing.
Model years: 1978
-
Column shift (power train)
Model years: 1975
-
Unknown or other
Model years: 1973
-
Suspension: lower ball joint
Model years: 1971
-
Labels (equipment)
Model years: 1973
-
Electrical system: wiring
Model years: 1971
-
Disc (service brakes)
Model years: 1971
-
Emission control (engine and engine cooling)
Model years: 1971
-
Vacuum (service brakes)
Model years: 1971
-
Vacuum (service brakes)
Model years: 1971
-
Suspension: lower ball joint
Model years: 1971
-
Arm (steering)
Model years: 1971
Other Dodge models
- Durango13,770 complaints
- Grand Caravan13,508 complaints
- RAM 150012,416 complaints
- Caravan10,526 complaints
- Dakota6,629 complaints
- RAM 25006,443 complaints
- Intrepid6,228 complaints
- Charger5,741 complaints
Source: NHTSA recall and complaint databases and EPA fuel economy data, October 2026. Complaint counts are owner reports to NHTSA, not verified defects. Recall counts are safety campaigns that list this model year; whether a particular car was already repaired depends on its VIN. How this data is compiled.