RecallMyCar

Winnebago CW822FT Recalls & Complaints by Model Year

NHTSA lists 7 safety recalls and 0 owner complaints across 1 model year of the Winnebago CW822FT (1990).

7
safety recalls, all years
0
owner complaints, all years
1990
year with most recalls

Pick your Winnebago CW822FT model year

Model yearRecallsComplaints
1990 Winnebago CW822FT70

All Winnebago CW822FT recalls (7)

Every NHTSA safety campaign that lists a Winnebago CW822FT, most recent first, with the model years each one covers.

  1. Wheels

    NHTSA 91V148000 Reported 160 vehicles potentially affected WINNEBAGO IND., INC.

    Road debris may enter an opening in the rear suspension trailing arm and damage the bearing seal.

    Remedy: Drill a 1/8 inch vent/drain hole, clean the bearing seal area, apply heavy washout resistant grease between the hub assembly and the trailing arm surfaces, and install a foam rubber plug into the angled opening at…

    Model years: 1990

  2. Hub (wheels)

    NHTSA 91V149000 Reported 160 vehicles potentially affected WINNEBAGO IND., INC.

    The front and rear wheel hub retainer nuts have been incorrectly torqued. The preload on the bearing from the loosened hub retainer nut may cause bearing failure.

    Remedy: Inspect bearing and replace if necessary. Torque the hub retainer nut 230 to 350 foot pounds.

    Model years: 1990

  3. Horn (electrical system)

    NHTSA 91V150000 Reported 160 vehicles potentially affected WINNEBAGO IND., INC.

    The horn activating switch components located in the steering column can wear abnormally.

    Remedy: Replace the steering wheel hub and horn brush. Arrange the parts to avoid the premature wear conditions.

    Model years: 1990

  4. Suspension: control arm

    NHTSA 91V151000 Reported 160 vehicles potentially affected WINNEBAGO IND., INC.

    The lower ball joint retaining nut that holds the lower ball joint to the steering knuckle was not torqued correctly.

    Remedy: Inspect lower ball joints, replace worn parts, and torque the lower ball joint mounting nut 130 to 150 foot pounds.

    Model years: 1990

  5. Rack and pinion (steering)

    NHTSA 91V152000 Reported 160 vehicles potentially affected WINNEBAGO IND., INC.

    The steering gear intermediate shaft clamps used to retain the intermediate shaft to the steering gear shaft and the column shaft can become loose because of incorrect bolt size and clamp force.

    Remedy: Replace the pinch bolts in the intermediate steering shaft assembly with 7/16" bolts. Torque bolts 63 to 75 foot pounds.

    Model years: 1990

  6. Gear box (other than rack and pinion) (steering)

    NHTSA 91V153000 Reported 160 vehicles potentially affected WINNEBAGO IND., INC.

    The steering gear mounting bracket bolts may become loose and allow the gear to move out of position.

    Remedy: Replace the mounting bolts; place a spacer plate between the steering gear mounting bracket and the left front frame; reattach the steering gear assembly mounting bracket to the frame using new hardened nuts torqued to…

    Model years: 1990

  7. Shock absorber (suspension)

    NHTSA 91V154000 Reported 160 vehicles potentially affected WINNEBAGO IND., INC.

    The rear shock absorber bracket causes the rear shock absorber lower mounting hardware to fail prematurely.

    Remedy: Remove old shock absorber mounting brackets, reattach new brackets to frame, adapt shock absorbers and add a jounce pad spacer between each jounce pad and the new shock absorber brackets.

    Model years: 1990

Other Winnebago models

Source: NHTSA recall and complaint databases and EPA fuel economy data, October 2026. Complaint counts are owner reports to NHTSA, not verified defects. Recall counts are safety campaigns that list this model year; whether a particular car was already repaired depends on its VIN. How this data is compiled.