Chrysler Lebaron Recalls & Complaints by Model Year
NHTSA lists 31 safety recalls and 629 owner complaints across 23 model years of the Chrysler Lebaron (1976–2003). The most-complained-about year is 1994.
Pick your Chrysler Lebaron model year
| Model year | Recalls | Complaints |
|---|---|---|
| 2003 Chrysler Lebaron | 0 | 1 |
| 1997 Chrysler Lebaron | 0 | 2 |
| 1996 Chrysler Lebaron | 0 | 3 |
| 1995 Chrysler Lebaron | 0 | 75 |
| 1994 Chrysler Lebaron | 0 | 102 |
| 1993 Chrysler Lebaron | 0 | 66 |
| 1992 Chrysler Lebaron | 2 | 78 |
| 1991 Chrysler Lebaron | 5 | 63 |
| 1990 Chrysler Lebaron | 2 | 68 |
| 1989 Chrysler Lebaron | 2 | 49 |
| 1988 Chrysler Lebaron | 0 | 32 |
| 1987 Chrysler Lebaron | 2 | 42 |
| 1986 Chrysler Lebaron | 4 | 25 |
| 1985 Chrysler Lebaron | 5 | 10 |
| 1984 Chrysler Lebaron | 1 | 7 |
| 1983 Chrysler Lebaron | 4 | 2 |
| 1982 Chrysler Lebaron | 4 | 1 |
| 1981 Chrysler Lebaron | 2 | 0 |
| 1980 Chrysler Lebaron | 1 | 0 |
| 1979 Chrysler Lebaron | 0 | 1 |
| 1978 Chrysler Lebaron | 3 | 2 |
| 1977 Chrysler Lebaron | 2 | 0 |
| 1976 Chrysler Lebaron | 2 | 0 |
What Chrysler Lebaron owners complain about
Across all model years, owners have filed 629 complaints with NHTSA. The 1994 model year has the most, with 102.
All Chrysler Lebaron recalls (31)
Every NHTSA safety campaign that lists a Chrysler Lebaron, most recent first, with the model years each one covers.
-
Latch (latches/locks/linkages)
The hood latch assembly may not have been properly installed and the secondary hood latch may be prevented from engaging when the hood is closed.
Remedy: Adjust the secondary hood latch to allow the latch assembly to properly engage when the hood is closed.
Model years: 1992
-
Steering wheel/handle bar (steering)
The zinc plating operation performed on the upper steering column shaft coupling bolt caused hydrogen embrittlement and breakage of the bolt.
Remedy: Replace the zinc plated bolt with a phosphate plated bolt.
Model years: 1992
-
Pads (service brakes)
The bonded disc brake linings may separate from the shoes due to a bonding deficiency which may allow corrosion degradation of the bond attachment.
Remedy: Replace the front and rear linings on vehicles with 15 inch brakes. Replace only the rear brake linings on vehicles with 14 inch brakes because the front linings on these vehicles are riveted.
Model years: 1989
-
Door (structure)
The owner's manual incorrectly states that the front passenger door cannot be opened from the inside if the door is locked until the lock control handle has been pulled up. On these vehicles, the front passenger door can be opened by the inside door handle even if the door is locked.
Remedy: Notify the vehicle owners of the error in the owner's manual and inform them of the actual operation of the front door lock system.
Model years: 1991
-
Anchorage (seat belts)
Front outboard safety belt may become difficult to latch and or unlatch due to a webbing stiffener entering the buckle housing and dislodging the buckle latch guide.
Remedy: Replace buckle latch engagement.
Model years: 1991
-
Linkage and cable (parking brake)
Mismatched parking brake cable lengths to the rear wheels reduces braking ability of one of the rear wheels, in violation of FMVSS 105.
Remedy: Replace mismatched parking brake cable with one of correct length.
Model years: 1991
-
Air bags: sensor/control module-inactive
The two air bag system front impact sensors may not be secured to their mounting brackets.
Remedy: Repair to assure proper attachment of front impact sensors to brackets.
Model years: 1991
-
Caliper (service brakes)
Front disc brake caliper guide pin bolts may not have been adequately torqued and could loosen.
Remedy: Properly torque front brake caliper guide pin bolts to 250 pounds.
Model years: 1991
-
Air bags: sensor/control module-inactive
Air bag inflator modules may not contain diffuser holes between the ignitor and propellant chambers.
Remedy: Replace air bag inflator modules with properly machined modules.
Model years: 1990
-
Engine (engine and engine cooling)
The engine valve cover gasket may dislocate and allow an engine oil leak at the gasket.
Remedy: Replace gasket cover with revised cover, and rtv sealant will be applied in place of a gasket.
Model years: 1989, 1990
-
Suspension: lower arm
Front suspension crossmember may corrode and fail at lower control arm rear pivot mounts if operated where salt is used to aid in snow removal.
Remedy: Install attachment reinforcement brackets to prevent control arm detachment as a result of corrosion weakening.
-
Seats
Drivers seat frame may experience fatigue failure at one (front/outboard) of its four attachments.
Remedy: Replace drivers seat frame with a strenghtened version; also, reinforce power adjuster front crossmember to increase rigidity of seat attachment system.
Model years: 1985
-
Fuel system, gasoline
Fuel leakage may occur in low ambient temperature operation at connections of an engine compartment fuel supply hose to the pressure regulator and to the fuel rail.
Remedy: Relocate pressure regulator; replace fuel supply with formed hose with revised routing configuration to ensure sealing integrity.
-
Power adjust (seats)
A service replacement drivers seat cushion (manual seat type) may contain wrong cushion with a brace that could interfere with power seat adjuster mechanism and cause stress on the frame.
Remedy: Replace frame with proper power seat frame.
-
Accelerator pedal (vehicle speed control)
Drivers floormat mispositioned such as to interfere with accelerator pedal.
Remedy: Floormat will be replaced with a redesigned mat to eliminate the interference.
Model years: 1987
-
12v/24v/48v battery (electrical system)
Battery cap vents may be partially or completely blocked with plastic flashing. Consequence of defect: a build up of internal gas pressure could occur which could result in case rupture, particularly during post charging. Should a person be in the vicinity of the battery when the case ruptures, they may be injured by the released gases…
Remedy: Rework batteries by probing both vent orifices to eliminate any vent obstruction.
Model years: 1986
-
Interior/under dash (electrical system)
A resistor in the electronic panel cluster may be subjected to an electrical current overload due to failure of a switching transistor. Consequence of defect: the overheated resistor could ignite and start an instrument panel fire.
Remedy: Modify instrument panel cluster by replacing the resistor with a fused resistor that will not ignite if overloaded.
Model years: 1986
-
Hoses, lines/piping, and fittings (fuel system)
An engine compartment fuel hose routed to the fuel system pressure regulator may have an inadequately tightened hose clamp. Consequence of defect: the fuel hose could leak and result in an engine compartment fire.
Remedy: Reposition and tighten to the proper torque level of the fuel hose clamp.
Model years: 1985
-
Seat belts: front
Required front center seat belt assembly was omitted. Vehicles are not in compliance with the requirements of federal motor vehicle safety standard 209, seat belt assemblies.
Remedy: Installation of missing center seat belt will be done without charge.
Model years: 1985
-
Hoses, lines/piping, and fittings (fuel system)
The potential for fuel leakage exists in the engine compartment at the fuel reservoir seam and its hose connections. The fuel reservoir is a silver colored can mounted to the air cleaner.
Remedy: The hoses and the metal tube that attaches to the fuel reservoir will be replaced with new components. The dealer will also replace or reseal the reservoir.
Model years: 1984
-
Hoses, lines/piping, and fittings (service brakes)
Hydraulic brake tubing routed to the left rear wheel brake system may have been bent out of shape during assembly and could chafe against the exhaust system hanger bolt.
Remedy: Dealer will inspect and relocate tube, if necessary. A retaining clip will be installed to ensure adequate clearance for the tubing; any damaged tubes will also be replaced.
Model years: 1983
-
Electrical (equipment)
The travel computer system wiring, on the involved vehicles, may be improperly connected. This condition can cause damage to internal components.
Remedy: The wiring will be reconnected to ensure proper functioning of ignition system..
Model years: 1983
-
Hoses, lines/piping, and fittings (service brakes)
On the involved vehicles, improper routing of the hydraulic brake tube could cause it to chafe against the park brake cables. Eventually, the brake tube may fail and brake fluid leakage may occur.
Remedy: Dealer will reroute the hydraulic brake tube, if necessary, without charge to owner.
Model years: 1983
-
Fluid (service brakes)
The brake hydraulic system bay be equipped with brake fluid containing an excess of water.
Remedy: Dealer will replace defective brake fluid without charge to owner.
Model years: 1982
-
Suspension: lower ball joint
Clamp bolts installed on certain vehicles may contain cracks. Eventually these bolts may break through, causing separation of the ball joint from the steering knuckle.
Remedy: Dealer will replace both ball joint stud clamp bolts without charge to owner.
Model years: 1982
-
Vehicle speed control
The automatic speed control switch may stick in the "resume" position restricting return movement. This will not allow the normal brake pedal operation to deactivate the system.
Remedy: The shield portion of the "resume" slide lever in the speed control unit will be replaced without charge.
Model years: 1981, 1982
-
Carburetor system (fuel system)
Engine may lose power or stall due to carburetor flooding. This is caused by a poor electrical ground on the carburetor fuel bowl vent solenoid. Vehicles may also have driveability problems while the engine is warming up in cold weather. These problems include engine missing, sags, and hesitation. This is caused by a sticking carburetor…
Remedy: Dealer will inspect carburetor and if necessary, the bowl vent solenoid will be repaired by resoldering (reconnecting) the external electrical connection free of charge. If applicable, the oxygen feedback sensor will…
Model years: 1981
-
Hoses, lines/piping, and fittings (service brakes)
The front brake hose routing on the involved vehicles may allow interference between the hoses and the front tires during extreme turning angles.
Remedy: Special brake hose restraining straps will be installed on each involved vehicle to relocate both front hoses and ensure that adequate hose to tire clearance is maintained.
Model years: 1980
-
Latch (latches/locks/linkages)
On the involved vehicles, the hood secondary catch system may be misaligned which may cause the secondary catch to malfunction. Consequently, the hood may not be securely latched.
Remedy: Dealer will adjust the catch system to fully secure the hood, without charge.
Model years: 1976, 1977, 1978
-
Steering wheel/handle bar (steering)
The columns may contain steering shafts in which the steering column coupling roll pin retaining notch was machined too deep. This may cause the steering wheel shaft to become disengaged from the rest of the steering assembly.
Remedy: Dealer will install a cotter pin through the roll pin to ensure retention, at no cost to owner.
Model years: 1978
-
Hoses, lines/piping, and fittings (service brakes)
On the involved vehicles, damage to the front wheel brake hydraulic system could occur due to front wheel brake line tube corrosion. Front wheel brake hoses may become brittle and crack due to prolonged operation in cold temperatures.
Remedy: The dealer will replace both front hoses if found necessary and in addition, will install a plastic shield between the battery thermo-guard and the tubes to prevent corrosion.
Model years: 1976, 1977, 1978
Other Chrysler models
- Town and Country13,517 complaints
- Pacifica7,008 complaints
- 3004,925 complaints
- 2004,187 complaints
- Sebring2,833 complaints
- Pt Cruiser2,524 complaints
- Concorde2,217 complaints
- 300C1,258 complaints
Source: NHTSA recall and complaint databases and EPA fuel economy data, October 2026. Complaint counts are owner reports to NHTSA, not verified defects. Recall counts are safety campaigns that list this model year; whether a particular car was already repaired depends on its VIN. How this data is compiled.